RedSealHeavyDutyExam

Sample questions: Heavy duty equipment technician exam

RedSealHeavyDutyExam · Topics · Exam guide · Sample questions

Practice questions written by us, with the correct answer and the rule cited. They are not official questions.

1. During cranking, a starter draws 250 A. The positive and negative cables each have a resistance of 0.002 ohm. What is the voltage drop across the negative cable?

  1. 0.50 V
  2. 0.05 V
  3. 1.00 V
  4. 5.00 V

Ohm's law gives V = I × R = 250 A × 0.002 ohm = 0.50 V across the negative cable (sub-task D-19.02, voltage drop). The value 1.00 V adds the resistance of both cables although only the negative cable is asked, 0.05 V comes from reading the resistance as 0.0002 ohm, and 5.00 V from reading it as 0.02 ohm.

2. What is the best way to collect an oil sample for trend analysis?

  1. Cold, after the machine sits overnight.
  2. Warm, from the same sampling valve.
  3. Warm, right after an oil change.
  4. Cold, from the reservoir drain plug.

A sample taken with the oil warm and circulating, from the same sampling valve each time, is representative and can be compared from one service to the next (sub-task G-34.01 includes collecting oil samples for analysis). Oil that has sat overnight lets particles and water settle out, so a cold sample misses them, and the drain plug collects settled sludge and water. A sample taken right after an oil change shows mostly new oil and hides the wear trend.

3. A machine loses power under load but idles normally. A vacuum gauge on the inlet of the transfer pump reads far above the limit in the service information. What is the most likely cause?

  1. A worn injector nozzle.
  2. A failed boost sensor.
  3. A leaking return line.
  4. A plugged suction filter.

High vacuum on the inlet side of the pump means fuel is struggling through a restriction upstream, such as a plugged filter or pickup, and the engine starves when load raises the demand (sub-task B-10.02). A worn nozzle changes spray and smoke, not inlet vacuum; a leaking return line does not create a suction restriction; and a failed boost sensor would set a code rather than restrict the fuel.

4. A transmission failed and metal debris went through its welded torque converter. What is done with the converter?

  1. Clean it with solvent.
  2. Backflush it with air.
  3. Replace the converter.
  4. Drain it and refill it.

A welded converter cannot be opened, so debris trapped between the impeller, turbine and stator cannot be removed reliably, and any leftover metal would destroy the rebuilt transmission; the converter is replaced and the cooler and lines are flushed (sub-task E-24.03). Air, solvent or a simple drain and refill leave debris behind, and solvent can also harm the seals.

5. On a hydraulic service brake system charged by accumulators, which component triggers the operator's alarm when stored accumulator pressure falls below a safe level?

  1. Stop lamp pressure switch.
  2. Low-pressure warning switch.
  3. Charging valve unloader spool.
  4. Accumulator precharge valve.

An accumulator-charged brake circuit uses a low-pressure warning switch that closes when stored pressure drops below its set point, lighting the warning lamp or sounding the alarm before the brake reserve is lost; checking that it works is part of diagnosing the system (sub-task C-15.02). The stop lamp pressure switch reacts to applied brake pressure, not stored pressure. The charging valve unloader spool only directs pump flow at cut-in and cut-out, and the precharge valve is a gas fill fitting with no signalling role.

6. A new hydraulic hose fails near the crimped end after a short time. The stripe along the hose spirals around it. What is the most likely cause?

  1. Twisted when fitted.
  2. The oil was too thick.
  3. Low pump pressure.
  4. Fitting over-torqued.

A stripe that spirals instead of running straight shows the hose was twisted when installed, and sub-task A-3.04 requires hoses to be routed to avoid twist, chafing and crush points; the twist stresses the reinforcement, so the hose fails near the fitting. Thick oil, low pump pressure and an over-torqued fitting would not twist the lay line of the hose.

7. Air enters an evaporator at 32 °C and leaves it at 5 °C. What is the temperature drop across the evaporator in °F, to the nearest degree?

  1. 15 °F
  2. 49 °F
  3. 27 °F
  4. 81 °F

The drop is 32 - 5 = 27 °C, and a temperature difference converts with the factor 1.8 only, so 27 x 1.8 = 48.6, or 49 °F to the nearest degree (sub-task F-32.02, measurements: temperature). Giving 27 °F skips the conversion, 15 °F divides by 1.8 instead of multiplying, and 81 °F wrongly adds 32 to a difference.

8. A crawler dozer rolled over and its ROPS frame is bent. What is done with the structure?

  1. Straighten it by heating the bends.
  2. Weld reinforcing plates over the bend.
  3. Reinstall it with new mounting bolts.
  4. Replace it with an approved structure.

A ROPS that has been deformed in a rollover has lost its tested strength, so it is replaced with a certified structure (sub-task H-38.03). Heating, welding plates or straightening it changes the steel and cannot restore the certification. New bolts do not correct a bent frame.

9. A series hybrid loader has the engine running at governed speed but will not move. The DC bus reads 0 V at the inverter input. Which component is checked first?

  1. The transmission clutch pack.
  2. The torque converter stator.
  3. The front driveshaft joints.
  4. The generator and its cables.

In a series drive the engine only turns the generator, which feeds the DC bus, and the traction motors are fed through the inverter, so with the engine at governed speed and no DC bus voltage, the generator and its output cables are checked first (sub-task I-40.02, hybrid equipment systems: series; measurements: generator output). A clutch pack, a converter stator and driveshaft joints are mechanical parts that cannot remove the DC bus voltage, and a series drive has no torque converter between the engine and the wheels.

10. A telematics unit sends engine hours and fault data to the portal, but the machine's position never updates. What is the most likely cause?

  1. An open CAN terminator.
  2. A weak cellular signal.
  3. A faulty GPS antenna.
  4. A failed engine ECM.

Data is arriving, so the cellular link, the data link and the engine ECM work, and only the position is missing, which points to the GPS antenna or its cable (sub-task D-22.02, remote monitoring systems (telematics)). An open terminator or a failed engine ECM would disrupt the engine data as well, and a weak cellular signal would delay every report, not only the position.

11. A crane boom holds its load well in neutral, but it lowers in jerks while the pump runs smoothly. Which valve is the most likely cause?

  1. Circuit relief valve.
  2. Counterbalance valve.
  3. Pressure reducing valve.
  4. Anti-cavitation valve.

Correct answer: Counterbalance valve. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

12. A cylinder has a swept volume of 1 125 cm3 and a clearance volume of 75 cm3 at top dead centre. What is the compression ratio?

  1. 16:1
  2. 15:1
  3. 14:1
  4. 17:1

Correct answer: 16:1. The step-by-step calculation, with the RSOS sub-task this question tests, is included in Premium access.

13. Which converter part redirects the oil returning from the turbine to the impeller?

  1. Lock-up piston.
  2. Impeller vanes.
  3. Turbine vanes.
  4. Stator vanes.

Correct answer: Stator vanes. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

14. A technician tests the voltage drop of the ground side of a charging circuit with the engine at fast idle and the loads on. Where are the voltmeter leads connected?

  1. Alternator stud and battery positive post.
  2. Battery positive post and negative post.
  3. Alternator housing and battery negative post.
  4. Alternator stud and alternator housing.

Correct answer: Alternator housing and battery negative post. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

15. In cold weather, moisture in a pneumatic line freezes. Which consumable is added to the alcohol evaporator?

  1. Methyl hydrate.
  2. Mineral spirits.
  3. Ethylene glycol.
  4. Hydraulic oil.

Correct answer: Methyl hydrate. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

16. A hydro-pneumatic strut must be removed from a haul truck. What is done before the mounting pins are loosened?

  1. Raise frame to full height.
  2. Block frame and vent gas.
  3. Add nitrogen to the strut.
  4. Loosen the rod gland nut.

Correct answer: Block frame and vent gas. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

17. A technician must disconnect a battery cable and top up the electrolyte on a large machine. Which PPE set is correct?

  1. Earplugs, dust mask, hard hat.
  2. Apron, gloves, face shield.
  3. Leather gloves, ear muffs, cap.
  4. Cotton gloves, safety cap, vest.

Correct answer: Apron, gloves, face shield. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

18. After a new turbocharger is installed, what must be done before the engine is first started?

  1. Run at high idle to seat the bearing.
  2. Fill the compressor housing with oil.
  3. Spin the wheel with compressed air.
  4. Prime the bearing with clean oil.

Correct answer: Prime the bearing with clean oil. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

19. What must be done before an ECM is reprogrammed with a laptop?

  1. Connect a stable power supply.
  2. Disconnect the other modules.
  3. Start the engine for voltage.
  4. Clear the stored fault codes.

Correct answer: Connect a stable power supply. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

20. What is the purpose of a clutch brake on a heavy-duty dry clutch?

  1. Release the pressure plate.
  2. Limit the release travel.
  3. Cushion the clutch engagement.
  4. Stop input shaft rotation.

Correct answer: Stop input shaft rotation. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

21. On a cold morning a gear pump rattles loudly, and the noise fades as the oil warms. A vacuum gauge at the pump inlet reads far above normal, and the oil level is correct. What is the most likely cause?

  1. Oil too thick for the cold.
  2. Worn gear pump bushings.
  3. Air leak at the shaft seal.
  4. Main relief valve stuck open.

Correct answer: Oil too thick for the cold. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

22. A technician replaces a ride height valve on an air suspension. How is the specified ride height set?

  1. Change the shock absorber.
  2. Shim the axle U-bolts.
  3. Adjust the valve linkage.
  4. Add air to the tires.

Correct answer: Adjust the valve linkage. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

23. The charge indicator light stays on while the engine runs at fast idle. The belt is tight and all connections are clean. What is the next step?

  1. Replace both batteries.
  2. Test the alternator output.
  3. Replace the drive belt.
  4. Replace the alternator.

Correct answer: Test the alternator output. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

24. What should be done before starting a newly installed piston pump for the first time?

  1. Start at full throttle to prime.
  2. Run it dry briefly to seat it.
  3. Fill the case with clean oil.
  4. Close the suction shutoff valve.

Correct answer: Fill the case with clean oil. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

25. A used oil sample from a diesel engine shows elevated sodium, potassium and glycol. What is the most likely source?

  1. Fuel dilution from the injectors.
  2. Coolant leaking into the oil.
  3. Dirt drawn in through the intake.
  4. Soot loading from combustion.

Correct answer: Coolant leaking into the oil. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

26. A final drive runs hot and noisy. The magnet holds large steel chips, and the oil analysis reports high iron. What is the next step?

  1. Open it and inspect gears.
  2. Refill with heavier oil.
  3. Replace the breather.
  4. Wipe the magnet and run.

Correct answer: Open it and inspect gears. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

27. What is the function of the heater core in a cab heating system?

  1. Filters dust from fresh air.
  2. Cools the air before the blower.
  3. Transfers coolant heat to cab air.
  4. Regulates coolant temperature.

Correct answer: Transfers coolant heat to cab air. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

28. After a two-way radio was added in a cab, the display flickers and a joystick reading jumps each time the radio transmits. The joystick tests normal with the radio off. What is the most likely cause?

  1. Low pilot pressure at the valve.
  2. A worn joystick return spring.
  3. Interference from the radio wiring.
  4. A failed operator seat switch.

Correct answer: Interference from the radio wiring. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

29. A hydraulic valve solenoid is removed from its circuit and its coil is measured. The coil reads 0.4 ohm and the service information gives 12 to 14 ohms. What is the most likely fault?

  1. An open coil winding.
  2. A failed suppression diode.
  3. A high-resistance connector.
  4. Shorted coil windings.

Correct answer: Shorted coil windings. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

30. A replacement hydrostatic motor is installed, and the loop is flushed and filled. What is done at the first start-up?

  1. Run at full throttle under load.
  2. Stall the motor to seat it.
  3. Shut off the charge pump flow.
  4. Idle unloaded, purging air.

Correct answer: Idle unloaded, purging air. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

31. A technician must measure a pin diameter to the nearest 0.01 mm (0.0004 in). Which tool is the best choice?

  1. Feeler gauge.
  2. Dial gauge.
  3. Micrometer.
  4. Depth gauge.

Correct answer: Micrometer. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

32. Two wheel nuts on a loader are found loose after the first shift. The nuts were torqued in a circular order in one pass, and the studs and tire pressures are in good condition. What is the most likely cause?

  1. Wrong tightening sequence.
  2. Overinflated drive tires.
  3. Damaged rim lock ring.
  4. Excess hub bearing preload.

Correct answer: Wrong tightening sequence. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

33. A weak exhaust brake is tested against the service information. A pressure gauge is installed and the brake is applied at the specified engine speed. Where is the gauge fitted?

  1. After the muffler outlet.
  2. In the charge air piping.
  3. At the turbo oil feed.
  4. Ahead of the brake valve.

Correct answer: Ahead of the brake valve. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

34. What is inspected after draining a powershift transmission to look for internal wear?

  1. Fill cap threads.
  2. Magnet and filter.
  3. Breather cap vent.
  4. Dipstick tube seal.

Correct answer: Magnet and filter. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

35. A serpentine belt on an alternator is held by a spring-loaded automatic tensioner. How is the belt load released for removal?

  1. Cut the belt with a knife.
  2. Pry the belt off the pulley.
  3. Rotate the tensioner with a tool.
  4. Loosen the alternator pivot bolt.

Correct answer: Rotate the tensioner with a tool. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

36. A technician measures margin pressure on a load-sensing pump with one gauge at the pump outlet and one on the load-sense line. How is margin calculated?

  1. Pump pressure minus load-sense pressure.
  2. Load-sense pressure minus pump pressure.
  3. Pump pressure plus load-sense pressure.
  4. Pump pressure minus return pressure.

Correct answer: Pump pressure minus load-sense pressure. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

Take the free test · full question bank and mock exams with a subscription