What this unit covers
MWA E of the RSOS: drivetrain systems, Tasks E-23 to E-29 (clutches, torque converters and retarders, manual and powershift transmissions, drive shafts, axles and final drives). These are original practice notes, not official Red Seal program material, based on the RSOS 2023. Service values (pressures, clearances, torques, intervals) always come from the manufacturer's service information. Safety practices are described in general terms: provincial rules can add requirements and regulatory thresholds can change.
Clutches, converters and retarders (RSOS Tasks E-23 and E-24)
- Free play: without it the release bearing rides on the fingers and the clutch slips; adjust before replacing parts (sub-task E-23.01). The clutch brake stops the input shaft for first or reverse.
- Stator: held by its one-way clutch, it redirects returning oil to multiply torque (sub-task E-24.01).
- Stall test: throttle held only long enough to read speed, since all power becomes heat (sub-task E-24.02). High stall in forward only, reverse normal: the forward clutch. A weak engine gives a low stall speed.
- Retarder: braking depends on oil admitted between rotor and stator, so control pressure is measured (sub-task E-24.02). A contaminated welded converter is replaced and the cooler flushed (sub-task E-24.03).
Manual transmissions and transfer cases (RSOS Task E-25)
- Backlash: one gear held, dial indicator on the other; a spring scale reads rolling torque (sub-task E-25.02).
- Grinding in one gear: worn synchronizer of that gear; a weak detent spring makes it jump out of gear (sub-task E-25.02).
- Both output seals leaking: plugged breather pressurizing the case (sub-task E-25.02).
Powershift transmissions (RSOS Task E-26)
- Oil level: engine running, oil at operating temperature, manufacturer's procedure (sub-task E-26.01).
- One range slips: the clutch applied only in that range. All ranges: the shared supply (pump, screen, main regulator) (sub-task E-26.02).
- Tests: a gauge at the test port reads clutch pressure. No speed signal with normal pressures: check the sensor and wiring first (sub-task E-26.02).
- Planetary ratio: ring held, sun input, carrier output: 1 + ring teeth / sun teeth. 1 + 78 / 30 = 3.6, so 1,800 rpm gives 500 rpm (sub-task E-26.02).
- Calibration: after new plates, seals or valve body, run the fill calibration with the electronic service tool (sub-task E-26.03). Burnt oil with friction material: slipping clutch packs.
Drive shafts (RSOS Task E-27)
- Phasing: yoke ears in the same plane, equal angles; out of phase gives vibration twice per revolution, a bent or unbalanced shaft once per revolution (sub-task E-27.02).
- Greasing: until clean grease purges at all four cups (sub-task E-27.01). Worn slip splines clunk on torque reversal.
Axles and differentials (RSOS Task E-28)
- Setup order: pinion depth and preload, then side bearing preload and backlash, contact pattern last (sub-task E-28.03).
- Diagnosis: noise only in turns points to spider gears; chatter in turns after an oil change, missing friction modifier; large chunks on the plug, open the axle (sub-task E-28.02). Fill to the bottom of the fill plug opening (sub-task E-28.01).
- Total reduction: ratios multiply: 36 / 9 = 4.0, × 4.5 = 18.0, so 1,800 rpm gives 100 rpm (sub-task E-28.02).
Final drives (RSOS Task E-29)
- Planetary: sun input, ring held, carrier output gives reduction (sub-task E-29.01). 1 + 72 / 18 = 5, with a 3:1 bevel pair 15:1.
- Metal face seals: rubber rings and seats clean and dry; reused rings stay as a matched pair (sub-task E-29.03).
- Inspection: drain plug magnet and oil checked on draining; large chips mean opening the unit (sub-tasks E-29.01, E-29.02).
Sample questions (5)
1. A dry clutch slips under load and the pedal has almost no free play left. What is the first correction?
- Replace the clutch disc.
- Replace the release bearing.
- Adjust the pedal free play.
- Resurface the flywheel.
Without free play the release bearing rides on the pressure plate fingers, so the clamping load is reduced and the clutch slips; restoring free play is the simplest and cheapest correction (sub-task E-23.01). The disc, the release bearing and the flywheel are replaced or machined only if the slipping continues after the adjustment and an inspection shows wear or damage.
2. A converter stall test is done with the wheels blocked and the brakes applied. How long is full throttle held?
- Just long enough to read speed.
- Until the converter fully locks up.
- Until the engine governs out.
- Until oil temperature stabilizes.
At stall the engine drives the converter while the turbine is held, so all of that power turns into heat in the oil; the throttle is held only long enough for the speed to be read and then released (sub-task E-24.02). Waiting for the oil temperature to stabilize or for the engine to reach governed speed risks overheating, and the lock-up clutch does not engage at stall.
3. During a stall test the engine speed is well above specification in forward but normal in reverse. The oil level is correct. What is the most likely cause?
- Low engine power output.
- Worn forward clutch.
- Seized stator sprag.
- Plugged suction screen.
A high stall speed means the turbine is not held as firmly as it should be; because reverse is normal, the converter, the pump and the oil supply common to both ranges are working, so the fault is in the clutch used only in forward (sub-task E-24.02). A weak engine would give a low stall speed, and a seized stator or a plugged oil screen would show up in both ranges.
4. A hydraulic retarder gives weak braking on a long downgrade. The oil level and temperature are normal. What is checked next?
- Retarder control pressure.
- Final drive oil condition.
- Converter stall speed test.
- Lock-up clutch condition.
A hydraulic retarder slows the machine by filling a chamber between a rotor and a stator with oil, and the braking force depends on how much oil the control valve admits, so once the level and temperature are normal the control pressure is measured (sub-task E-24.02). Stall speed tests the converter, not the retarder, and the final drive oil and the lock-up clutch are not part of the retarder circuit.
5. A transmission failed and metal debris went through its welded torque converter. What is done with the converter?
- Clean it with solvent.
- Backflush it with air.
- Replace the converter.
- Drain it and refill it.
A welded converter cannot be opened, so debris trapped between the impeller, turbine and stator cannot be removed reliably, and any leftover metal would destroy the rebuilt transmission; the converter is replaced and the cooler and lines are flushed (sub-task E-24.03). Air, solvent or a simple drain and refill leave debris behind, and solvent can also harm the seals.