What this unit covers
MWA F of the RSOS: heating (Task F-30), ventilation, filtration and cab pressurization (Task F-31), air conditioning (Task F-32) and sound suppression (Task F-33). These are original practice notes, not official Red Seal program material, based on the 2023 RSOS. Service values (pressures, charge quantities, intervals) always come from the manufacturer's service information. For refrigerant handling, provincial rules can add requirements and regulatory thresholds can change.
Heating (Task F-30)
- Heater core: a small radiator; hot engine coolant flows through it and the blower pushes cab air across its fins (sub-task F-30.01).
- Hot, pressurized coolant: let the system cool and relieve its pressure before opening a valve or hose; an auxiliary heater can run with the engine stopped, so it is switched off, cooled and its power isolated first (sub-task F-30.03).
- Refilling: vacuum fill equipment draws the circuit down, then pulls in coolant, leaving no air pockets in the heater core (sub-task F-30.03).
No-heat diagnosis (sub-task F-30.02)
- Low temperature gauge, engine never warms up: thermostat stuck open.
- Hot inlet hose, cold outlet hose: coolant is not flowing through the core, which is restricted.
- Both hoses hot, gauge normal: the fault is in the air path, such as a blend door that does not travel fully to hot.
- Uneven hose temperatures: trapped air.
Ventilation and pressurization (Task F-31)
- HEPA: high efficiency particulate air; this element traps the finest dust and allergens, while foam pads and washable screens stop only larger debris (sub-task F-31.01).
- Seals: lubricated only with the rubber-safe lubricant the manufacturer specifies (sub-task F-31.01); dust entering past a new filter points to leaking door or window seals, because the cab only stays pressurized when they close tightly (sub-task F-31.02).
- Blower speeds: resistors drop the voltage for low and medium; an open resistor leaves only high speed working (sub-task F-31.02).
Air conditioning (Task F-32)
- Recovery: a certified person recovers the refrigerant into a container designed for it before the system is opened; refrigerant is never released, and federal regulations follow the same principle (sub-task F-32.01).
- Evacuation: vacuum lets moisture boil off at low temperature and draws air out; moisture forms acids, and air raises head pressure (sub-task F-32.03).
- Leak testing: use dry, inert nitrogen, not shop air; federal regulations forbid charging a system with a halocarbon only to leak test it (sub-task F-32.02).
- Gauge readings: pressures moving toward each other mean worn compressor valves or pistons; both sides high on a correct charge mean a dirty condenser; a restriction pulls the low side down (sub-task F-32.02).
- Freeze-up: the evaporator ices when nothing cycles the compressor off, such as a faulty evaporator temperature sensor (sub-task F-32.02).
- Temperature difference: difference in °F = difference in °C × 1.8, with no 32 added; a drop from 32 °C to 5 °C is 27 °C, about 49 °F (sub-task F-32.02).
Sound suppression (Task F-33)
- Decibel meter: reads cab sound level for comparison with the manufacturer's value (sub-task F-33.02).
- Oil-soaked foam: repair the leak, then replace the foam, secured as the service information directs (sub-task F-33.03).
Sample questions (5)
1. What is the safe first step before removing the heater control valve on a hot engine?
- Drain half the coolant out.
- Close the heater hose clamps.
- Run the engine at fast idle.
- Cool it and release pressure.
Coolant at operating temperature is under pressure and can scald, so the system must cool and its pressure be relieved before any valve or hose is opened (sub-task F-30.03, hazards: hot fluids, pressurized fluids). Draining first still leaves hot, pressurized coolant at the valve, fast idle keeps the engine hot, and clamps on the hoses do not relieve system pressure.
2. After a heater core is replaced, which tool best removes air from the cooling circuit as it is refilled?
- Cooling system pressure tester.
- Coolant vacuum fill equipment.
- Radiator flushing gun nozzle.
- Coolant refractometer tester.
Vacuum fill equipment draws the circuit down and then pulls in coolant, so no air pockets are left in the heater core (sub-task F-30.03, tools: coolant vacuum fill equipment). A pressure tester only checks for leaks, a flushing gun cleans scale but does not purge air during refilling, and a refractometer measures coolant freeze protection.
3. A technician must service a fuel-fired auxiliary coolant heater. What is done before its lines are disconnected?
- Stop the engine and open them.
- Let it cool and isolate power.
- Drain the fuel tank first.
- Switch it off and open them.
A fuel-fired auxiliary heater heats the coolant and can run with the engine stopped, so it is switched off, allowed to cool and its power is isolated before any line is opened (sub-task F-30.03, hazards: hot surfaces, hot fluids, pressurized fluids). Stopping the engine does not stop the heater, switching it off and opening the lines at once exposes the technician to hot, pressurized coolant, and draining the fuel tank does nothing about heat or electrical power.
4. In cold weather, a loader's cab heater blows only lukewarm air and the temperature gauge stays well below normal after an hour of work. Both heater hoses are equally warm. What is the most likely cause?
- Plugged heater core.
- Stuck-open thermostat.
- Blend door stuck cold.
- Air in the circuit.
An engine that never reaches operating temperature, shown by the low gauge, is sending coolant through the radiator all the time, which points to a thermostat stuck open (sub-task F-30.02). A plugged core or trapped air would leave the engine at normal temperature with one hose cold or uneven, and a stuck blend door does not change the gauge.
5. A crawler dozer's cab heater blows cold air at full hot. The engine is at normal temperature, the coolant level is full, the heater inlet hose is hot and the outlet hose is cold. What is the most likely cause?
- Weak coolant pump.
- Bad blower resistor.
- Plugged heater core.
- Low coolant level.
A hot inlet hose proves coolant reaches the core, but a cold outlet hose shows it is not flowing through, so the core passages are restricted (sub-task F-30.02, tests: temperature; conditions: flow restrictions). A weak coolant pump would slow flow through the whole engine rather than stop it in the core alone, the full coolant level rules out a low level, and a bad resistor changes air speed, not coolant flow.