What this unit covers
MWA C of the RSOS: steering (Task C-13), suspension (Task C-14), brakes (Task C-15), undercarriage (Task C-16) and wheel assemblies (Task C-17). These are original practice notes, not official Red Seal program material, based on the 2023 RSOS. Service values (pressures, clearances, torques, intervals) always come from the manufacturer's service information. Provincial safety rules can add requirements.
Steering (Task C-13)
- HMU: the hand metering unit sends a measured volume of oil to the cylinders for each turn of the wheel; the priority valve gives steering first call on flow (sub-task C-13.01).
- Secondary steering: a ground-driven or electric pump lets the machine steer to a safe stop if primary supply fails (sub-task C-13.01).
- Articulation lock: installed before opening the circuit so the frame cannot pivot and crush anyone (sub-task C-13.01).
- Diagnosis: hard steering only at low engine speed points to a worn pump (flow test); more turns lock to lock, to internal HMU wear; a dragging steering brake makes a dozer pull to that side and heats that compartment (sub-task C-13.02).
- Service: fill a motor case with clean oil before first start; bleed by steering slowly lock to lock at low idle, then recheck the oil level (sub-task C-13.03).
- Cylinder force: Force = pressure × piston area, with area = π × d² / 4; an 80 mm bore at 10 000 kPa gives about 50 kN (sub-task C-13.03).
Suspension (Task C-14)
- Hydro-pneumatic struts: charged with nitrogen, which is inert and dry; with the oil level correct, a strut that sags and rides harshly has lost gas pressure (sub-tasks C-14.01, C-14.02).
- Strut removal: block the frame, vent the gas charge (sub-task C-14.03).
- Ride control: accumulator gas cushions lift-circuit spikes; with no gas pressure the bounce is not absorbed (sub-task C-14.02).
- Pivots, springs, height: pin-to-bushing clearance is compared with the service information; a leaf pack that lost its arch lowers that side; ride height valves are set by linkage length (sub-tasks C-14.01 to C-14.03).
Brakes (Task C-15)
- Spring-applied parking brake: held on by springs, kept off by hydraulic pressure; loss of pressure applies it (sub-task C-15.01).
- Accumulator circuits: release and isolate trapped oil pressure first (sub-task C-15.01); read precharge with oil pressure released; low precharge makes pressure drop quickly after a small draw; a low-pressure warning switch alerts before the reserve is lost (sub-task C-15.02).
- Drag: pressure trapped in the apply line (restricted return from the brake valve) keeps discs clamped (sub-task C-15.02).
- Air brakes: cage the power spring of a spring brake chamber before loosening the clamp band (sub-task C-15.03); excess stroke with an automatic slack adjuster is a fault to find, not hand-adjust (sub-task C-15.01); a missing wheel speed signal means testing the sensor, wiring and connector first (sub-task C-15.02).
Undercarriage (Task C-16)
- Grease adjuster: release tension slowly through the relief valve, never by unscrewing the fitting (sub-task C-16.01).
- Recoil spring: fit a retaining tool before disassembly (sub-task C-16.03).
- Wear: clean the links, measure several pitches; Wear % = (average pitch − new pitch) / new pitch × 100 (sub-task C-16.02).
- Tension: too tight wears pins, bushings and sprocket early; too slack can throw the track; one-sided wear with correct sag points to alignment (sub-task C-16.02).
Wheels and tires (Task C-17)
- Multi-piece rims: deflate fully (remove the valve core) before disassembly; stored air can throw the lock ring (sub-task C-17.01).
- Inflation: in a tire inflation cage, with a remote chuck and hose, standing clear (sub-task C-17.03).
- Wheel nuts: star pattern, in stages, rechecked when specified (sub-task C-17.02).
- Runout: measured with a dial indicator; a bent rim causes shimmy (sub-task C-17.02).
Sample questions (5)
1. In a hydrostatic steering system, which component meters oil to the steering cylinders in proportion to steering wheel rotation?
- Priority flow valve.
- Steering cylinder.
- Hand metering unit.
- Flow control valve.
The hand metering unit (HMU) passes a measured volume of oil to the cylinders for each turn of the steering wheel, which is the operating principle of hydrostatic steering in sub-task C-13.01. The priority flow valve only gives the steering circuit first call on pump flow, the cylinder is the actuator that moves, and a flow control valve limits flow rate without regard to wheel rotation.
2. A technician must replace a steering cylinder hose on an articulated loader. What is done before the hose is loosened?
- Steer the frame fully left.
- Install the articulation lock.
- Raise the loader arms fully.
- Run the engine at high idle.
The articulation lock is installed so the frame halves cannot pivot and crush a person while the circuit is opened; this is the crush point and stored energy hazard handled in sub-task C-13.03. Steering the frame over or raising the arms leaves the machine free to move, and running the engine at high idle keeps the pump supplying pressure to the line being opened.
3. A hydraulic steering motor on a differential steer crawler has been replaced. What is done before the first start?
- Pressurize the motor case.
- Run the motor briefly dry.
- Plug the case drain line.
- Fill the case with oil.
Pre-lubrication and bleeding procedures are part of sub-task C-13.03: the case is filled with clean oil so the bearings and rotating group are lubricated at the first start. Starting the motor dry can score the parts, pressurizing the case can blow the shaft seal, and plugging the case drain traps leakage oil and builds case pressure.
4. An articulated loader steers normally at high idle but is hard to turn at low idle. The relief setting and cylinder leakage test are within specification. What is the most likely cause?
- Leaking cylinder seal.
- Worn steering pump.
- Seized articulation pin.
- Plugged tank breather.
Low engine speed already lowers pump output, so a worn pump that cannot deliver enough flow at low rpm shows up as hard steering only there; a flow gauge confirms it, as listed in sub-task C-13.02. The cylinder leakage test rules out a leaking seal, a seized articulation pin would make steering stiff at every speed, and a plugged breather does not cut flow only at low rpm.
5. A crawler dozer with clutch-and-brake steering pulls to the left when travelling straight with both levers released. The left steering clutch and brake compartment is much hotter than the right. What is the most likely cause?
- Dragging left brake.
- Worn right idler wheel.
- Loose left track pad.
- Slipping right clutch.
A steering brake that drags holds back the left track and heats the left compartment, so the machine pulls left; this matches the drifting and tracking symptoms in sub-task C-13.02. A slipping right clutch would slow the right track and heat the right compartment, a worn idler wheel causes wear without a one-sided heat build-up, and a loose track pad does not hold the track back.