What this unit covers
MWA D of the RSOS: charging systems (Task D-18), starting systems (Task D-19), batteries (Task D-20), electrical components and circuits (Task D-21) and electronic systems, modules and networks (Task D-22). These are original practice notes, not official material of the Red Seal program, and they are based on the RSOS 2023. Service values such as pressures, clearances, torques and intervals always come from the manufacturer's service information.
Charging systems
- Alternator: the stator produces alternating current and the rectifier diodes convert it to direct current; the regulator limits voltage (sub-task D-18.01).
- Belt: wear on one side of a correctly tensioned belt means misaligned pulleys, checked with a straightedge (sub-task D-18.01).
- Voltage drop: measured while current flows, output stud to battery positive for the positive side, alternator housing to battery negative for the ground side (sub-task D-18.02).
- 24 V systems: a 12 V load on one battery unbalances the pair; a voltage equalizer or a 24-to-12-volt converter corrects it (sub-task D-18.02).
- Rotor test: continuity from a slip ring to the shaft means a grounded winding; infinite ohms between the slip rings means an open winding (sub-task D-18.03).
Starting systems
- Ether: never used with an active grid heater or glow plugs (sub-task D-19.01).
- Cranking circuit: cable voltage drop is read while the starter cranks; never an ohmmeter on a live circuit (sub-task D-19.02).
- Solenoid: it clicks but nearly full battery voltage across its main contacts means burnt or worn contacts (sub-task D-19.02).
- Air starter: the stored air is released and isolated before the starter is disconnected (sub-task D-19.03).
Batteries
- Ratings: reserve capacity is minutes at a stated load before voltage falls to a set limit; cold cranking amps rate starting current (sub-task D-20.01).
- Load test: valid only at or near full charge, so recharge first (sub-task D-20.01).
- Series and parallel: series adds voltage, parallel adds capacity; four 12 V 150 Ah batteries in two series pairs joined in parallel give 24 V and 300 Ah (sub-task D-20.01).
- Boosting: the last connection goes on bare engine metal away from the battery, where hydrogen collects (sub-task D-20.02).
- Parasitic draw: if the draw stops with one fuse out, the loads of that circuit are unplugged one at a time (sub-task D-20.02).
Circuits and components
- Ohm's law: U = R × I; in series, resistances add. 4 and 8 ohms on 24 V: 12 ohms, 2 A, and 2 × 4 = 8 V across the 4-ohm resistor (sub-task D-21.02).
- Components: a capacitor smooths spikes and noise, a resistor limits current, a diode blocks reverse current (sub-task D-21.02).
- Meters: voltage in but not out of a closed switch means open contacts; a clamp goes around one conductor only, an inline ammeter in series (sub-task D-21.02).
- Fuses: a fuse that keeps blowing means finding the overload or short to ground, never fitting a higher rating (sub-task D-21.02).
Electronic systems and networks
- CAN terminators: two good 120-ohm terminators in parallel read about 60 ohms; 120 ohms means one is open or missing, near zero means the two wires are shorted (sub-task D-22.02).
- Sensors: a temperature signal shorted to ground reads very hot; an open signal or open sensor ground reads very cold. A transducer at 0.0 V with a signal-low code: check the signal wire for a short to ground, harness disconnected and power off (sub-task D-22.02).
- Calibration: replaced manipulators and valves are calibrated so the module learns neutral and end positions (sub-task D-22.01).
- Telematics: data arrives but no position points to the GPS antenna or its cable (sub-task D-22.02).
- Welding: batteries and ECM connectors disconnected per the service information, ground clamp close to the weld (sub-task D-22.03).
Sample questions (5)
1. What is the function of the rectifier in an alternator?
- Limits alternator voltage.
- Converts stator AC to DC.
- Magnetizes the rotor core.
- Filters radio interference.
The stator produces alternating current, and the rectifier diodes convert it to direct current for the batteries and loads (sub-task D-18.01, alternator components include rectifiers and diodes). Limiting the voltage is the job of the regulator, the rotor is magnetized by field current in its own winding, and radio interference is filtered by the alternator capacitor, not by the rectifier.
2. A machine with a battery disconnect switch needs its alternator removed. Which step makes the output wire safe to disconnect?
- Turn the ignition key switch off.
- Remove the alternator drive belt.
- Open the battery disconnect switch.
- Unplug the regulator wiring harness.
The alternator output stud is wired directly to the battery positive and stays live with the key off, so the batteries are isolated by opening the battery disconnect switch before the output wire is removed; a wrench touching the stud and the frame then cannot cause a short (sub-task D-18.01, release and isolate stored energy). The ignition key switch does not cut the output circuit, and removing the drive belt or unplugging the regulator wiring harness leaves the output wire live.
3. A new alternator belt squeals and shows wear on one side only. The belt tension is within the service information specification. What is the most likely cause?
- Misaligned pulleys.
- Open rectifier diode.
- Low regulator setting.
- Worn rotor bearing.
Wear on one side of a belt that is correctly tensioned shows the pulleys are not in line, so the belt runs at an angle; alignment is checked with a straightedge (sub-task D-18.01). A worn rotor bearing makes noise but does not wear one side of the belt, and an open diode or a low regulator setting changes charging output, not belt wear.
4. With the engine at fast idle and the voltmeter negative lead on the battery negative post, the meter reads 14.3 V at the alternator output stud, which is within specification, but only 12.6 V at the battery positive post. What is the most likely cause?
- Corroded charging cable.
- Open rectifier diode.
- Shorted stator winding.
- Faulty voltage regulator.
Both readings share the same ground point, so the 1.7 V difference is lost between the output stud and the battery positive post; a corroded or loose charging cable or connection is the likely cause, confirmed by a voltage drop test on the positive side under load (sub-task D-18.02). An open diode or a shorted stator would lower the voltage and current at the stud itself, and a faulty regulator would change the stud voltage, not leave it normal.
5. A multimeter set to AC volts and connected across the battery with the engine at fast idle reads well above the service information limit. What is the most likely cause?
- Slipping drive belt.
- Failed rectifier diode.
- Worn rotor slip rings.
- Low regulator setting.
A good rectifier changes the stator AC into smooth DC; when a diode opens or shorts, AC ripple reaches the battery and the AC reading rises (sub-task D-18.02). A slipping belt, a low regulator setting or worn slip rings can reduce output, but they do not push AC into the DC circuit.