RedSealHeavyDutyExam

🏗️ Structural Components, Operator Stations, Attachments and Accessories

What this unit covers

MWA H of the RSOS: structural components, operator stations, attachments and accessories, Tasks H-37 to H-39. These are original practice notes, not official Red Seal program material, based on the RSOS 2023. Service values (pressures, clearances, torques, intervals) always come from the manufacturer's service information. Safety practices are described in general terms: provincial rules can add requirements and regulatory thresholds can change.

Crack detection (RSOS Task H-37)

Structural repair (RSOS Task H-37)

  1. Drill a small hole at the crack tip to remove the sharp end where stress concentrates (sub-task H-37.03).
  2. Follow the approved procedure: unplug the modules and clamp the welding ground on clean metal of the same frame close to the weld, never on an axle shaft, battery post or cylinder rod (sub-task H-37.03).
  3. Preheat thick sections as specified: slower cooling lowers the risk of hard, brittle metal and cracking (sub-task H-37.03).

Pins, bushings and articulation (RSOS Task H-37)

Operator protective structures and seat belts (RSOS Task H-38)

Controls, interlocks and cameras (RSOS Task H-38)

Attachments and accessories (RSOS Task H-39)

Take the free test · full question bank and mock exams with a subscription

Sample questions (5)

1. A technician needs to find fine surface cracks on a steel boom. A coloured liquid is drawn into the cracks and a developer then makes them show. Which test is this?

  1. Ultrasonic thickness testing.
  2. Magnetic particle inspection.
  3. Dye penetrant inspection.
  4. Hydrostatic pressure testing.

Dye penetrant inspection uses crack penetrating dye, a test listed in sub-task H-37.02: the coloured liquid enters surface cracks and the developer draws it back out so the crack shows. Magnetic particle inspection uses a magnetic field and iron powder, not a liquid dye. Ultrasonic thickness testing measures remaining metal with sound, and hydrostatic testing pressurizes a closed component, so neither shows fine surface cracks on a boom.

2. A technician plans magnetic particle testing on several machine parts. Which part can be checked with this method?

  1. A steel frame rail.
  2. A brass fuel fitting.
  3. An aluminum cab step.
  4. A rubber engine mount.

Magnetic particle testing (magnaflux, listed in sub-task H-37.02) works only on materials that can be magnetized, such as the carbon steel of a frame rail. Aluminum and brass are not magnetic, so the iron particles would not outline a crack. Rubber is not magnetic either, and an engine mount is not a steel structural part.

3. A technician finds a 150 mm (6 in) crack in a boom side plate. The service information approves a welded repair. What is done at the end of the crack before the repair is prepared?

  1. Tack weld across the tip.
  2. Drill a stop hole at the tip.
  3. Grind a sharp notch at the tip.
  4. Peen the plate at the tip.

A small hole drilled at the tip of the crack removes the sharp end where stress concentrates, so the crack stops growing while the repair is prepared (sub-task H-37.03). Tack welding across the tip leaves the stress point in place, and a sharp notch makes a new stress riser. Peening the plate does not stop a crack that is already open.

4. A technician will arc weld a repair on a loader frame that carries electronic control modules. Where is the welding ground clamp attached?

  1. On the nearest wheel axle shaft.
  2. On the battery negative post.
  3. On a nearby hydraulic cylinder rod.
  4. On the frame, close to the weld.

The clamp goes on clean metal of the same frame close to the weld, so the welding current takes the shortest path and does not pass through modules, bearings or seals (sub-task H-37.03); the modules are also unplugged as the approved procedure directs. An axle shaft sends current through its bearings, the battery post leads it through the electrical system, and a cylinder rod can be pitted by arcing.

5. The approved procedure for repairing a crack in a thick, high-strength steel frame section calls for preheating the metal before welding. What is the main purpose of preheating?

  1. To raise the strength of the base metal.
  2. To slow cooling and limit weld cracking.
  3. To burn off the paint and the rust.
  4. To help the filler metal flow farther.

Preheating slows the cooling of the weld zone in a thick section, which lowers the risk of hard, brittle metal and cracking (sub-task H-37.03). It does not raise the strength of the base metal. Paint and rust are removed by cleaning and grinding before welding, and filler metal flow is controlled by the welding settings and technique; it is not the reason preheat is specified.

Start free

RedSealHeavyDutyExam · Topics · Exam guide · Sample questions