What this unit covers
MWA B of the RSOS: engines and supporting systems, Tasks B-5 to B-12 (base engine, lubrication, intake, exhaust, engine management, fuel delivery, emission control and cooling). These are original practice notes, not official Red Seal program material, based on the RSOS 2023. Service values (pressures, clearances, torques, intervals) always come from the manufacturer's service information. Safety practices are described in general terms: provincial rules can add requirements and regulatory thresholds can change.
Base engine (RSOS Task B-5)
- Displacement: swept volume of one cylinder times the number of cylinders. Displacement = π / 4 × bore × bore × stroke × cylinders; a 12 cm bore and 14 cm stroke give 1 583 cm3 per cylinder, or 9.5 L for six (sub-task B-5.02).
- Valve lash: checked at TDC on the compression stroke, both valves closed and followers on the cam base circle, then set to the service information (sub-task B-5.01).
- Compression brake: opens the exhaust valves near the top of the compression stroke, releasing the compressed air so the engine absorbs work (sub-task B-5.01).
- Smoke: blue smoke, oil consumption and heavy blow-by point to worn rings and liners (sub-task B-5.02); black smoke to a plugged air cleaner; white smoke with coolant loss to a head gasket.
Lubrication and oil analysis (RSOS Task B-6)
- Low oil pressure: confirmed first with a mechanical gauge (RSOS Task B-6).
- Glycol with sodium and potassium: coolant is entering the oil, for example through a cooler or gasket (sub-task B-6.02).
- Silicon with iron and aluminum: dust is getting past the air cleaner or an intake joint and wearing rings, liners and pistons (sub-task B-6.02).
Intake and exhaust (RSOS Tasks B-7 and B-8)
- New turbocharger: clean oil poured into the oil inlet and the shaft turned by hand before the feed line is connected (sub-task B-7.03).
- Inlet restriction: the vacuum it creates can pull oil past the compressor seal; it also causes black smoke and power loss (sub-task B-7.02). Never run the engine without the air filter.
- Exhaust leaks: found by soot trails and by listening from a safe distance (sub-task B-8.02).
- Heat shields: keep surface temperature down and brush, hoses and wiring away, limiting fire risk (sub-task B-8.03).
Engine management (RSOS Task B-9)
- Static: the technician is grounded, for example with a wrist strap, before touching ECM circuits (sub-task B-9.02).
- Cylinder cut-out test: no speed drop when a cylinder is cut out means it was not producing power; further tests find why (sub-task B-9.02).
- Intermittent code: harness and connectors are inspected before any sensor or ECM work (sub-task B-9.02).
Fuel delivery (RSOS Task B-10)
- Water separator: keeps water from the pumps and injectors (sub-task B-10.01).
- High inlet vacuum: restriction upstream of the pump, such as a plugged filter (sub-task B-10.02).
- Waxy gel on the filter: fuel below its cloud point; warm the system, replace the filter, use winter fuel or an additive (sub-task B-10.02).
- Injector correction code: entered with the electronic service tool (sub-task B-10.03). Never loosen a high pressure fitting with the engine running.
Emission control and cooling (RSOS Tasks B-11 and B-12)
- Soot and ash: regeneration burns soot; ash stays until the DPF is cleaned or replaced (sub-task B-11.02). Low exhaust temperature at idle calls for a stationary regeneration, parked clear of combustibles. Let the system cool before work (sub-task B-11.03). DEF never goes in the fuel tank.
- Wet liners: nitrite resists cavitation pitting; a low reading is corrected with a compatible coolant conditioner (sub-tasks B-12.01, B-12.02).
- Mix: 55 L at 40 % concentrate = 22.0 L concentrate and 33.0 L water (sub-task B-12.02).
- Pressure cap: raises the boiling point; never opened hot (RSOS Task B-12).
Sample questions (5)
1. A six-cylinder diesel has a bore of 120 mm and a stroke of 140 mm. What is its displacement?
- 9.5 L
- 1.6 L
- 12.1 L
- 38.0 L
Displacement is the swept volume of one cylinder times the number of cylinders: pi/4 x 12 cm x 12 cm x 14 cm = 1 583 cm3, and x 6 = 9 500 cm3, or 9.5 L (sub-task B-5.02, measurements). The 12.1 L figure leaves out the pi/4 factor, the 38.0 L figure uses the bore as a radius, and the 1.6 L figure forgets to multiply by the six cylinders.
2. A used haul truck engine burns oil, puffs blue smoke at idle and has heavy crankcase blow-by. What is the most likely cause?
- Worn rings and liners.
- Leaking head gasket.
- Worn injector nozzles.
- Plugged air cleaner.
Blue smoke, oil consumption and heavy blow-by together show oil passing worn rings and liners into the chamber while combustion gas leaks down into the crankcase (sub-task B-5.02). A plugged air cleaner gives black smoke, a leaking head gasket points to coolant loss and white smoke, and worn nozzles spoil the spray pattern without burning crankcase oil.
3. During a cylinder leakage test the piston is at top dead centre on compression with both valves closed. Shop air is applied and a steady hiss is heard at the exhaust pipe. What does this show?
- Leaking head gasket.
- Leaking intake valve.
- Leaking exhaust valve.
- Worn piston rings.
Air that escapes at the exhaust pipe is passing the exhaust valve of the cylinder under test (sub-task B-5.02, cylinder leakage test). Air at the intake would point to the intake valve, bubbles in the coolant to a head gasket or cracked head, and air at the crankcase breather or oil fill to worn rings.
4. On an overhead-valve diesel, where is a cylinder's piston placed so that both of its valves can be checked for lash?
- TDC on the compression stroke.
- Midway down the intake stroke.
- TDC on the exhaust stroke.
- Start of the exhaust stroke.
At top dead centre on the compression stroke both valves of that cylinder are closed with their followers on the base circle of the camshaft, so the lash of both can be checked and then set to the service information (sub-task B-5.01, valve lash). At TDC on the exhaust stroke the valves overlap and are both slightly open, midway down the intake stroke the intake valve is open, and at the start of the exhaust stroke the exhaust valve is already opening, so the gap read there is false.
5. A technician must measure the crankshaft end play on an assembled engine. Which method is used?
- Dial indicator, prying shaft endwise.
- Plastic gauge strip on main journals.
- Micrometer reading on rod journals.
- Bore gauge reading in main bearings.
End play is the fore-and-aft movement of the shaft, so a dial indicator is set on the shaft end and read while the shaft is pried endwise, then compared with the service information (sub-task B-5.02, measurements). A plastic gauge strip and a bore gauge check oil clearance in the bearings, and a micrometer on the rod journals checks wear and taper, none of which show axial movement.